buku manual canon 30d

File Name:buku manual canon 30d.pdf
Size:3582 KB
Type:PDF, ePub, eBook, fb2, mobi, txt, doc, rtf, djvu
Category:Book
Uploaded14 May 2019, 21:30 PM
InterfaceEnglish
Rating4.6/5 from 745 votes
StatusAVAILABLE
Last checked7 Minutes ago!

buku manual canon 30d

The EOS 30D is a high-performance, digital AF SLR camera with a large, fine-detail, 8.20-megapixel CMOS sensor. The camera has nine high-precision AF points, and it is compatible with all Canon EF lenses (including the EF-S lenses). EOS 30D INSTRUCTION MANUAL Software Guide Gives an overview of the bundled software and explains the software installation procedure.High-voltage internal parts can cause electrical shock. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. To recharge the battery, see page 22. Attach the lens. For EF lens When attaching an EF-S lens, align it with the white dot on the camera. For other lenses, align it with the red dot. Set the lens focus mode switch to. Focus the subject. Aim the AF point over the subject and press the shutter button halfway to autofocus. Basic Zone All you do is press the shutter button. 1: Full Auto (p.46) For fully automatic shooting. Image Zone Fully automatic shooting for specific subjects.: Portrait (p.48) 3: Landscape (p.48): Close-up (p.48): Sports (p.49) Be sure it is set to. In the text, the. Attaching the Strap Pass the end of the strap through the camera’s strap mount from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. When you remove the battery from the camera, be sure to reattach the cover to protect against short circuit. If the battery is left in the camera for a prolonged period without the camera being used, a low electrical current may be discharged excessively and the battery’s service life may be affected. Battery Pack BP-514, BP-511, or BP-512 can also be used. Checking the Battery Level When the switch is set to or (p.30), the battery level will be indicated at one of four levels.http://www.ecojardin.pl/files/bosch-hmd-5331-manual.xml

The actual number of shots may be fewer than indicated above depending on the shooting conditions. Do not connect or disconnect the power cord while the camera’s switch is set to. Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrow. Although the thickness is different, a Type I or Type II CF card can be inserted into the camera. The camera is also compatible with Microdrive and CF cards with 2 GB or higher capacity. While the access lamp is lit or blinking, do not do any of the following. Doing so may damage the image data, CF card, or camera. To save battery power, the camera turns off automatically after 1 minute of non- operation. To turn on the camera again, press the shutter button or other button.If you press the shutter button completely without pressing it halfway first or if you press the shutter button halfway and then press it completely immediately, the camera will take a moment before it takes the picture. Operating the. While looking at the LCD monitor, you use the button, button, and dial on the camera back to proceed to the next step. The explanation of menu functions hereinafter assumes that you pressed the. The Language screen will appear. Set the desired language. Turn the dial to select the language, then press. Each captured image is recorded with the date and time it was taken. Make sure you set the date and time correctly. If any dust adheres on the image sensor, it may show up as a dark speck on the images. To avoid this, follow the procedure below to clean the image sensor. Using the AC Adapter Kit ACK-E2 (optional, see page 26, 184) is recommended. If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens E (10 types, optional) is recommended. In each mode, the AF mode, metering mode, ISO speed, etc., are set automatically to suit the subject. With nine AF points to focus the subject, anyone can easily take nice pictures.http://www.friz.ch/userfiles/bosch-hmv9305-installation-manual.xml

AF point Focus confirmation light Shutter speed Aperture Set the Mode Dial to. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus. When the CF card becomes full, the CF Full warning “FuLL CF” will appear in the viewfinder and on the LCD panel and shooting will be disabled. Portrait Landscape Close-up This mode blurs the background to make the human subject stand out. Holding down the shutter button executes continuous shooting. In the or mode, if the shutter speed display blinks, be aware that camera shake may occur. This is for fast-moving subjects when you want to freeze the action. You can use self- timer in any Basic Zone mode or Creative Zone mode. Do not stand in front of the camera when you press the shutter button to start the self-timer. The asterisk M on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8). In the 1 mode, the captured image will require post-processing with the software provided.A higher ISO speed number indicates a higher sensitivity to light. Therefore, a high ISO speed is suited for low light and moving subjects. However, the image may look more coarse with noise, etc. You can also adjust the settings of each Picture Style to obtain custom image effects.To obtain natural-looking, black-and-white images, set a suitable white balance.To shoot with the Picture Style you modified, follow step 2 on page 56 to select the Picture Style and then shoot. A color can be brightened by using a filter having a similar or same color. At the same time, the complementary colors will be darkened. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal images, sRGB is recommended. In the Basic Zone modes, sRGB will be set automatically. With a digital camera, the color temperature can be adjusted with software so that the colors in the image look more natural.

The subject’s white color is used as the criteria for adjusting the other colors. By selecting this image, you import its white balance data for the white balance setting. Spot metering Photograph a white object. This adjustment will have the same effect as using a color temperature conversion or color compensating filter. Each color can be corrected to one of nine levels. Users familiar with using color temperature conversion or color compensating filters will find this feature handy. This is called white balance bracketing. With white balance bracketing, the maximum burst will be lower.The images you take are automatically assigned a file number from 0001 to 9999 and saved in a folder that can hold up to 9999 images. It will start from folder number 100 and file number 0001. This is convenient when you want to organize images according to CF cards. Camera Setting Display CF card remaining capacity Flash exposure compensation (p.106) Auto power off (p.43) For details on the image info. In the Basic Zone modes, the AF mode, AF point selection, metering mode, and drive mode are set automatically. Three AF modes are provided. One-Shot AF is suited for still subjects, while AI Servo AF is for moving subjects. And AI Focus AF switches from One-Shot AF to AI Servo AF automatically if the still subject starts moving. If this occurs, a picture cannot be taken even if the shutter button is pressed completely. Recompose the picture and try to focus again. This is for obtaining correct focus at the moment of exposure. The AF point can be selected automatically by the camera or manually by you. In Basic Zone modes and the mode, the AF point is selected automatically. In the modes, you can switch between automatic and manual AF point selection. Lens’ Maximum Aperture and AF Sensitivity The EOS 30D’s AF sensor has nine AF points. The center AF point is a high-precision, cross-type sensor sensitive to both vertical and horizontal lines of the subject.

The top and bottom AF points are vertical line-sensitive, and the remaining six AF points are horizontal line- sensitive AF points. This is called “focus lock.” Focus lock works only in the One-Shot AF mode. If the AF mode is AI Servo AF (or AI Focus AF set to Servo mode), focus lock will not work. In the Basic Zone modes, evaluative metering will be set automatically.In the Basic Zone modes, the optimum drive mode is set automatically. During continuous shooting, the captured images are first stored in the camera’s internal memory and then successively transferred to the CF card. When the internal memory becomes full during continuous shooting, “buSY”. After you press the shutter button halfway and let go, the timer operation will keep the LCD panel and viewfinder information displayed for about 4 sec. The camera automatically sets the shutter speed and aperture to suit the subject’s brightness.Increase the ISO speed or use flash. If “8000” and the minimum aperture blink, it indicates overexposure. Decrease the ISO speed or use an ND filter (optional) to reduce the amount of light entering the lens. This is called shutter-priority AE. A fast shutter speed can freeze the motion of a fast- moving subject and a slow shutter speed can blur the subject to give the impression of motion. Turn the dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure. Turn the dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. This is called aperture-priority AE.If the “8000” shutter speed blinks, it indicates overexposure.To determine the exposure, refer to the exposure level indicator in the viewfinder or use a handheld exposure meter. This method is called manual exposure. Set the exposure. Check the exposure level and set the desired shutter speed and aperture.: Standard exposure level. It is effective for group photos and landscapes.

The camera uses the nine AF points to detect the nearest and farthest subjects to be in focus. You can make the image look lighter (increased exposure) or darker (decreased exposure). Increased exposure Decreased exposure The exposure compensation amount will remain in effect even after the. This is called Auto Exposure Bracketing (AEB). Standard exposure AEB amount Standard exposure Decreased exposure Increased exposure Decreased exposure. If the drive mode is set to single image (u), you must press the shutter button three times. By locking the exposure, you can recompose the shot while maintaining the same exposure setting. This is called AE lock. It is effective for backlit subjects. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. This prevents mirror vibrations which may blur the image during close-ups or when a super telephoto lens is used.During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. However, you can turn on the illumination for about 6 sec. Connecting the Remote Switch You can attach to the camera any EOS accessory equipped with an N3 type plug such as the Remote Switch and Timer Remote Controller (both optional). The result is natural- looking flash photos. In the Basic Zone modes (except ), flash photography is fully automatic. Using the Built-in Flash in the Basic Zone If necessary, the built-in flash will pop-up automatically in low-light or backlit conditions. (except in modes) Using the Built-in Flash in the Creative Zone Regardless of the light level, you can press the. The camera’s red-eye reduction feature turns on the red-eye reduction lamp to shine a gentle light into the subject’s eyes to narrow the pupil diameter or iris. If the subject is too far away and beyond the effective range of the flash, the icon will blink. Get closer to the subject and repeat steps 2 to 4. Check that the.

Increased exposure Decreased exposure If you set flash exposure compensation with both the EX-series Speedlite and camera, the Speedlite’s flash exposure compensation setting will override the camera’s. You can easily do the flash operations below. For detailed procedures, see the Speedlite’s instruction manual. E-TTL II Autoflash E-TTL II is a new autoflash exposure system incorporating improved flash exposure control and lens focusing distance information, making it more precise than the previous E-TTL (evaluative flash metering with preflash) system. If the EX-series Speedlite’s firing mode is set to TTL autoflash with the Custom Function, the Speedlite will not fire. If autofocus cannot be achieved, the external, EOS-dedicated Speedlite’s AF-assist beam (if the Speedlite has an AF-assist beam) will be emitted automatically (except in the. For images taken with another camera: The camera might not be able to properly display images captured with a different camera or edited with a personal computer or whose file name was changed. If you press the. The brightness adjustment screen will appear. You can view a single image, the shooting information, an index display, or a magnified view.The horizontal axis indicates the brightness level (darker on the left and brighter on the right), while the vertical axis indicates how many pixels exist for each brightness level. Switching from the index display to another display format To display a single image, press the button. Pressing the button switches to the single image display and pressing it again switches to magnified view. Jump bar Playback the image. Display a single image, image with shooting information, index, or magnified view. Or turn it counterclockwise to jump backward by 10 or 100 images. Each image will be displayed for about 3 sec. During auto play, auto power off will not work. The display time may vary depending on the image. During auto play, you can press the.

Images will then be displayed in the correct orientation during playback. You can rotate the image even after you change the display format to shooting info display or index display after step 1. Always turn off the camera and the television before connecting or disconnecting them. Video IN terminal If the proper video system format is not set, the image will not be displayed properly. Image protect icon Once an image is protected, it cannot be erased by the camera’s erase function. To erase a protected image, you must first cancel the protection. If you erase all the images (p.125), only the protected images will remain. Only protected images (p.123) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Formatting a CF card will erase everything in the card. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer images to a personal computer before formatting the card. The camera enables direct printing with printers compatible with “ PictBridge”, Canon “ CP Direct”, and Canon “ Bubble Jet Direct.”. After “Preparing to Print” on the next page, follow the instructions applicable to your printer on the pages indicated.Setting the Camera For direct printing, using AC Adapter Kit ACK-E2 (optional) to power the camera is recommended.If you use a battery to power the camera, make sure it is fully charged. During direct printing, keep checking the battery level. If there is a long beeping sound in step 5, it indicates a problem with the PictBridge printer. Some settings might be disabled. For details, refer to your printer’s instruction manual.If your printer cannot print Borderless borderless prints, the print will have borders. Bordered The print will have a white border along the edges.Contrast Saturation Detail set.

Color tone Color balance After making fine adjustments for the printing effect, if you do step 4 again to change the printing effect’s setting, the adjustments will all revert to the default. The Adjust levels screen will then appear. B is for blue, A is amber, M is magenta, and G is green. Check that the icon is displayed on the upper left of the LCD monitor. Turn the. Turn the dial to select the menu item, then press. Turn the dial to select the desired setting, then press. The image will also be cut off along all four edges.Check that the icon is displayed on the upper left of the LCD monitor. Turn the. Paper Borders Date Set the number of copies. Set the trimming. S Printing with Bubble Jet Direct Turn the dial to select the menu item, then press. Turn the dial to select the desired setting, then press. The date will appear on the lower right of the image.Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again.The smaller you make the trimming frame, the grainier the picture will look. If the picture will be too grainy, the trimming frame will turn red. While trimming the image, look at the camera’s LCD monitor. To use the same settings again, follow the steps below. With Easy Printing, only one print can be printed each time. With Easy Printing, any cropping (trimming) will not be applied. It is for images taken with a digital camera, and you can specify which photos and the quantity to print. With a DPOF-compatible digital camera,. RAW images cannot be selected for printing.The order screen will appear. Select the image to be printed. Turn the dial to select the image to be printed. To deselect it, leave the box unchecked. Press to checkmark the box, or press again to remove the checkmark. For standard-type prints, a quantity of one will be ordered for all the images. Note that after following the “Selecting Individual Images” procedure, if you do the “Selecting All Images”.

PictBridge Prepare to print. See “Setting the Camera” (steps 1 and 2) and “Connect the camera to the printer” (steps 1 to 5) on pages 129 to 130. With PictBridge, the file No.When the camera is connected to a personal computer, you can transfer the images directly with the camera. This feature is called direct image transfer. If the computer software (EOS DIGITAL Solution Disk CD-ROM) provided with the. The Transfer order screen will appear. Note that after following the “Selecting Individual Images” procedure, if you do the “Selecting All Images” procedure, the transfer order will change to “All images.” 3 Selecting the Images to be Transferred Exit the menu. The selected images might all be overwritten. Also, depending on the image type, the transfer order may not be possible.You can then transfer images in the CF card to the personal computer by operating the camera.The EOS Utility’s default setting will sort the transferred images into folders sorted according to the shooting date.The transfer image selection screen will appear. Custom Functions work only in Creative Zone modes. Select Custom Function No. Turn the dial to select the setting, then press. The Clear settings screen will appear.The exposure level will be displayed in the viewfinder and on the LCD panel as shown below. C.Fn-07 You can enable the built-in flash, external Speedlite, and non-Canon flash connected to the PC terminal to fire. When “Auto cancellation” is set, bracketing will be canceled in the following cases: AEB: You turn the. Since automatic flash exposure compensation will not be executed, you may have to set it yourself depending on the scene. While the button is pressed, AF operation with the camera is disabled. 2: AE lock When the button is pressed, AE lock is applied. Convenient when you want to focus and meter separately. It covers information on camera features, system accessories, and other reference information. When focus is achieved, it is locked.

With evaluative uSingle metering, the exposure shooting setting is also locked. (The exposure setting is stored in memory before the shot is taken.) The above conditions. The combinations of shutter speed and aperture automatically determined by Program AE are shown as lines with respect to the subject brightness (Exposure Value) gradations on the left and top edges of the graph. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power Source The battery cannot be recharged. You are using the wrong battery. Do not recharge any battery pack other than Battery Pack BP- 511A, BP-514, BP-511, or BP-512. Auto power off is in effect. Press the shutter button halfway.The lens focus mode switch is set to. Set the lens focus mode switch to. (p.27) Camera shake occurred when you pressed the shutter button. To prevent camera shake, hold the camera still and press the shutter button gently. Error Code Communications between the camera and lens is Err 01 faulty. Clean the lens contacts. (p.11) There is a problem with the CF card. AC Adapter Kit ACK-E2 Power source kit (AC adapter, DC coupler, power cord) for supplying power to the camera with a household power outlet. Compatible with 100 - 240 V AC. Compact Power Adapter CA-PS400 Quick charger for BP-511A. You can fire only one or both flash tubes and control the flash ratio to easily obtain sophisticated lighting effects with E-TTL II autoflash. Remote Switch RS-80N3 This is a remote switch to prevent camera shake for super-telephoto shots, macroshooting, and bulb. The camera’s specifications and physical appearance are subject to change without notice. The cable with the ferrite core provided with the digital camera must be used with this equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules. The 13-digit and 10-digit formats both work. Please try again.Please try again.Used: GoodPages are in great shape.

Something we hope you'll especially enjoy: FBA items qualify for FREE Shipping and Amazon Prime. Learn more about the program. Not yet ready for a comprehensive book on digital SLR photography. This book serves as a guide to the purpose and function of your 30D's basic controls, how to use them, and why. You'll get a quick introduction to focus zones, Bokeh, flash synchronization options, how to choose zoom settings and exposure modes. Unlike the manual, this book cuts through the confusion and menu listings to provide exactly the information that is needed. It serves as a perfect product-specific book to using your Canon EOS 30D. Then you can start reading Kindle books on your smartphone, tablet, or computer - no Kindle device required. In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Register a free business account As a roving photojournalist for more than twenty years, he illustrated his books, magazine articles, and newspaper reports with award-winning images. He's operated his own commercial studio, suffocated in formal dress while shooting weddings-for-hire, and shot sports for a daily newspaper and upstate New York college. During the past year, he's had as many as five of his books listed in the Top 20 of Amazon.com's Digital Photography Bestseller list--simultaneously. Busch's 120-plus other books published since 1983 include bestsellers like David Busch's Quick Snap Guide to Digital SLR Lenses. Visit his website at If you are a seller for this product, would you like to suggest updates through seller support ? To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon.

It also analyzes reviews to verify trustworthiness. Please try again later. La Chatte 4.0 out of 5 stars If that describes you, it's a wonderful book. It's a lot more interesting and user-friendly than the instruction manual for the 30D, but if you're a serious amateur or a pro who's converted to digital, it's simplistic. That's not to say I haven't found it helpful. There isn't really anything that I didn't already know, but the presentation is well done and it makes for great quick reference. I was hoping for something a little more advanced when I ordered it, so in that respect I was disappointed. So, about the 4 star rating I gave it. It's an average: 3 stars if you're an adept photographer, 5 stars if you're not so experienced.This book explains so much more than the owner's manual and its a million times easier to read and understand. There are a few times when I have had to flip back and forth to find illistrations so that I can understand what function we are applying to it. I think that is true of any book but I do feel the illistrations are placed better within the book than most books are. I have enjoyed having it and it fits well in my big camera bag so I can take it with me and refer to it. WELL WORTH the money and time!However, if you have somewhat of an understanding for photography i would pass on it. In my opinion it is just a fancier version of the instruction manual that came with the camera. It has decent illustrations and is well written. It's a nice book for anyone who has recently bought a Canon 30D and serves as a good reference book.Buy this book. I've only begun using it and I sure wish I'd seen it was available when I first bought my 30d. No, it is not just a rehash of the Canon manual - it actually explains the how AND why.Seriously! This book leaves no stone unturned when it comes to operating and understanding the Canon 30D. Well done.Met and exceeded all my expectations. I would buy another if I needed one!

Breakdown of topics and writing level are excellent.The technical level of the content is just right to keep you interested but does not insult your intiligence.Sorry, we failed to record your vote. Please try again He has found it very helpful.Sorry, we failed to record your vote. Please try again. Somewhere between the tedious user manual full of technical garble and the generic how to digital photography books is the ideal guide to your EOS 30D. Welcome to that guide. Canon EOS 30D Guide to Digital SLR Photography provides you with a concise introduction to the most important features specific to your EOS 30D, explaining not only how to use them but also why and when. Filled with full-color images to illustrate results in various settings, this book also helps you enhance your digital photography skills with techniques specific to the EOS 30D. A full-color book with spectacular imagesLet us know YOUR RECENTLY VIEWED ITEMS Browsing History ON Clear History Not responsible for typographical or illustrative errors. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. Finished book size is A5 (148 x 210mm). 100 pages long. Our reprints are high quality, printed on 80gsm super-white Canon paper on a Canon office copier. The pages are then spiral bound with a clear acetate front cover and red card back cover, held together with a strong white wire. Your manual will lay flat when open and will last for as long as your camera, with a little bit of care. Manuals over 400 pages long may be supplied as more than one book. Find low everyday prices and buy online for delivery or in-store pick-up. Download and Read Manual Canon Eos 30d Manual Canon Eos 30d Where you can find the manual canon eos 30d easily. Is it in the book store. Quick Start Guide 1 2 3 4 5 6 Canon Casio Contarex Contax Canon EOS 30D Camera User Manual.

Total Pages in Manual: 201 Why order your Instruction Manual from Manuals Ink.com? How do I E0S 30D LCD Monitor, how accurate for exposure. Shop with confidence. Canon EOS 70D User Manual Available For Download (EOS 70D with and without WiFi) The Canon EOS 70D user manual can be downloaded from this link. Nutritional guide for fuddruckers, Modified cash statement, Alan keyes petition argument against standing, Dell professional 1708fp 17in resolution, Dm500 user manual. Reload to refresh your session. Reload to refresh your session. Please try again.Please try your request again later. As an avid photographer, you owe it to yourself to make the most out of your cutting-edge equipment. Somewhere between the tedious user manual full of technical garble and the generic how to digital photography books is the ideal guide to your EOS 30D. Welcome to that guide. Canon EOS 30D Guide to Digital SLR Photography provides you with a concise introduction to the most important features specific to your EOS 30D, explaining not only how to use them but also why and when. Filled with full-color images to illustrate results in various settings, this book also helps you enhance your digital photography skills with techniques specific to the EOS 30D. In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Then you can start reading Kindle books on your smartphone, tablet, or computer - no Kindle device required. Get your Kindle here, or download a FREE Kindle Reading App.If you are a seller for this product, would you like to suggest updates through seller support ? Amazon calculates a product's star ratings based on a machine learned model instead of a raw data average. The model takes into account factors including the age of a rating, whether the ratings are from verified purchasers and factors that establish reviewer trustworthiness. Sorry, we failed to record your vote.